In 1943 there was some attempt on making low silhouette trucks. Also GMC was involved.
It was on a 151 inch wheelbase frame and sported a big winch in front.
And it looks as they managed to get it only two inches lower than the open cabbed CCKW..... when frontwindow and tarps down..
Any more info on this??
What was the range of serialnumbers? And henche to the wheelbase. I have not found any other GMC with this wheelbase. Was it a "brand new frame" used?
There was also some trails on the CCKW 352 trucks with wb 145 inches. here they managed to get the silhouette 4 inches lower. More info on these?
There was also some trucks dessignated DAKW and DOKW
Rolf
GMC DCKW "low silhouette"
-
- First Lieutenant
- Posts: 122
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Norway
- Contact:
GMC DCKW "low silhouette"
One of the best MV club-magazines in the world...
Have a look at the Norwegian MV-clubs site at www.hmkf.no
Have a look at the Norwegian MV-clubs site at www.hmkf.no
-
- Brigadier General
- Posts: 2595
- Joined: Thu Jun 08, 2006 1:10 am
- Location: San Antonio, Texas
Neat web site. Thanks.
52 M38 Willy's
Former owner and restorer of CCKW353 " Betty Boop"
proud father of a career Army officer/Blackhawk pilot/ War in Iraq veteran
Retired high school history teacher at Lt. Colonel Robert G. Cole CMH High School, Fort Sam Houston Texas
proud great grandson of four Confederate soldiers.
great great grandson of a War of 1812 veteran
great great great grandson of 2 American Revolutionary war veterans
Former owner and restorer of CCKW353 " Betty Boop"
proud father of a career Army officer/Blackhawk pilot/ War in Iraq veteran
Retired high school history teacher at Lt. Colonel Robert G. Cole CMH High School, Fort Sam Houston Texas
proud great grandson of four Confederate soldiers.
great great grandson of a War of 1812 veteran
great great great grandson of 2 American Revolutionary war veterans
-
- Brigadier General
- Posts: 2400
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Pembroke NH
- Contact:
I believe that they were only prototypes and thus single units or just a few.
The problem with a GMC low silhouette truck would be the combination of a vertical OHV engine and the front axle. Have you ever noticed the intentional 'dent' in the CCKW oil pan? It is there for a reason...
The problem with a GMC low silhouette truck would be the combination of a vertical OHV engine and the front axle. Have you ever noticed the intentional 'dent' in the CCKW oil pan? It is there for a reason...
Dr Deuce Over 50,000 driven miles in a CCKW
1942 CCKW closed cab shopvan
1943 CCKW closed cab cargo w/M32 MG mount
1944 CCKW open cab LeRoi Kompressor
1944 CCKW open cab F1 Aircraft fueler tanker
1945 CCKW open cab cargo w/artic cab
1942 Chev cargo
1942 Chev K51 Panel
1944 Chev M6 Bomb Truck
1942 GPW Jeep
http://home.comcast.net/~cckw/wsb/html/ ... 59870.html
1942 CCKW closed cab shopvan
1943 CCKW closed cab cargo w/M32 MG mount
1944 CCKW open cab LeRoi Kompressor
1944 CCKW open cab F1 Aircraft fueler tanker
1945 CCKW open cab cargo w/artic cab
1942 Chev cargo
1942 Chev K51 Panel
1944 Chev M6 Bomb Truck
1942 GPW Jeep
http://home.comcast.net/~cckw/wsb/html/ ... 59870.html
-
- First Lieutenant
- Posts: 122
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Norway
- Contact:
Axels moved forward
I know of the oil pan "problems"...
But on the DCKW (at least) the front axel is moved forward so it actually is in front of the radiator to acomodate the problem.
And also wondering why it took that long time before GMC came with the two pice oilpan, so the engines could fit on both Timken and GM frames..
Rolf
But on the DCKW (at least) the front axel is moved forward so it actually is in front of the radiator to acomodate the problem.
And also wondering why it took that long time before GMC came with the two pice oilpan, so the engines could fit on both Timken and GM frames..
Rolf
One of the best MV club-magazines in the world...
Have a look at the Norwegian MV-clubs site at www.hmkf.no
Have a look at the Norwegian MV-clubs site at www.hmkf.no