Cargo bed Data Plate
-
- Captain
- Posts: 188
- Joined: Thu Jun 08, 2006 1:10 am
- Location: East coast
- Contact:
Cargo bed Data Plate
I have a all steal cargo bed 353 , is the data plate located " front of bed drivers side " and are there more than one plate on this type bed ? If someone has a picture they can post of this plate because mine has been sandblasted some time or other and is very faint .
GMC CCKW 353, M29 weasel, 1/2 ton dodge, Ben Hur Trailer
- Cat Man
- Major
- Posts: 420
- Joined: Thu Jul 20, 2006 9:55 pm
- Location: Green Bay WI
Bed Data Plate
Hi Snow Man,
Yes, the all steel body has one data plate on the left front corner. My camara just refused to photo it. Says Disk Error - Oh NO!!!
The tags are always faint from weather. And they were not very deep anyway. The tag is the size of a business card. Four rivets in the corners
The data tag reads:
FOR PARTS REQUISITION
BODY MODEL NO. 08395-Z
80 X 144
MANUFACTURED BY
EDW. G. BUDD MFG CO
PHILADELPHIA - DETROIT
DELIVERY DATE _________________
Hope that helps
Cat Man
Yes, the all steel body has one data plate on the left front corner. My camara just refused to photo it. Says Disk Error - Oh NO!!!
The tags are always faint from weather. And they were not very deep anyway. The tag is the size of a business card. Four rivets in the corners
The data tag reads:
FOR PARTS REQUISITION
BODY MODEL NO. 08395-Z
80 X 144
MANUFACTURED BY
EDW. G. BUDD MFG CO
PHILADELPHIA - DETROIT
DELIVERY DATE _________________
Hope that helps
Cat Man
40 Years An Engine Guy
30 Years A Caterpillar Guy
Still Learning Every Day
30 Years A Caterpillar Guy
Still Learning Every Day
-
- Captain
- Posts: 188
- Joined: Thu Jun 08, 2006 1:10 am
- Location: East coast
- Contact:
Thanks Cat Man , i was in the process of getting a new plate and the vendor said there could be two on the bed . The plate you describe is the one i have the only deference is mine is attached with small Philips head screws . Is yours similar to a "pop rivet " or a solid head brad ?
GMC CCKW 353, M29 weasel, 1/2 ton dodge, Ben Hur Trailer
- Cat Man
- Major
- Posts: 420
- Joined: Thu Jul 20, 2006 9:55 pm
- Location: Green Bay WI
Cargo Bed data plate
I think the plate on the bed I have was held on with Phillps head screws also.
Cat Man
Cat Man
40 Years An Engine Guy
30 Years A Caterpillar Guy
Still Learning Every Day
30 Years A Caterpillar Guy
Still Learning Every Day
-
- First Lieutenant
- Posts: 96
- Joined: Thu Jun 08, 2006 1:10 am
- Location: San Diego, CA
- Contact:
-
- First Lieutenant
- Posts: 87
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Holland
- Contact:
- Cat Man
- Major
- Posts: 420
- Joined: Thu Jul 20, 2006 9:55 pm
- Location: Green Bay WI
Cargo Bed data plate
Interesting thread. Here are two photo's of the tag on an all steel 1950's replacement bed made in Europe. German??
One tag only. No extra holes, same size and location as on my early all steel US built bed.
Cat Man
One tag only. No extra holes, same size and location as on my early all steel US built bed.
Cat Man
40 Years An Engine Guy
30 Years A Caterpillar Guy
Still Learning Every Day
30 Years A Caterpillar Guy
Still Learning Every Day
-
- Second Lieutenant
- Posts: 43
- Joined: Fri Mar 23, 2007 5:36 am
- Location: southern france
-
- Captain
- Posts: 188
- Joined: Thu Jun 08, 2006 1:10 am
- Location: East coast
- Contact:
Re:
Where are those plates located on the bed , and do you think they are original to the truck ?Kees51 wrote:There usually are two plates on an all steel bed...
http://www.pbase.com/kees_s/image/79984578
GMC CCKW 353, M29 weasel, 1/2 ton dodge, Ben Hur Trailer
-
- Captain
- Posts: 210
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Switzerland
Do you know where to buy reproductions of these bed plates?
1942 GMC CCKW 353 cargo closed cab with steel bed
1943 Dodge WC 63 (6x6)
1944 Jeep Willys
1943 steel Ben Hur trailer
194? 1 ton Buffalo water trailer
194? 1/4 ton Bantam trailer
Link to see my vehicules: http://ledog.forumgmc.com
-
- Captain
- Posts: 188
- Joined: Thu Jun 08, 2006 1:10 am
- Location: East coast
- Contact:
Re:
I have some on the way and will post some pic's then you can decide if you like them .777 AAA wrote:Do you know where to buy reproductions of these bed plates?
GMC CCKW 353, M29 weasel, 1/2 ton dodge, Ben Hur Trailer
-
- Captain
- Posts: 210
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Switzerland
Re:
Great!snow man wrote:I have some on the way and will post some pic's then you can decide if you like them .777 AAA wrote:Do you know where to buy reproductions of these bed plates?
1942 GMC CCKW 353 cargo closed cab with steel bed
1943 Dodge WC 63 (6x6)
1944 Jeep Willys
1943 steel Ben Hur trailer
194? 1 ton Buffalo water trailer
194? 1/4 ton Bantam trailer
Link to see my vehicules: http://ledog.forumgmc.com
-
- First Lieutenant
- Posts: 87
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Holland
- Contact:
Re:
They were at the right front side, at the drivers side. They looked exactly like the plates I saw on an original wooden bed of a AFKWX a while ago, so I think they were genuine. Those plates also were at that position, and there also were two, with the same kind of information per plate as the ones pictured here.snow man wrote:Where are those plates located on the bed , and do you think they are original to the truck ?Kees51 wrote:There usually are two plates on an all steel bed...
http://www.pbase.com/kees_s/image/79984578
This is the truck they were on:
http://www.pbase.com/kees_s/image/79984580
Unfortunately I didnt get to speak with the owner, so I dont know anything more about it.
I photographed it because I rarely see such a neat set of original data plates on a cargo bed, and I look at many.
-
- Captain
- Posts: 210
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Switzerland
1942 GMC CCKW 353 cargo closed cab with steel bed
1943 Dodge WC 63 (6x6)
1944 Jeep Willys
1943 steel Ben Hur trailer
194? 1 ton Buffalo water trailer
194? 1/4 ton Bantam trailer
Link to see my vehicules: http://ledog.forumgmc.com
-
- Captain
- Posts: 188
- Joined: Thu Jun 08, 2006 1:10 am
- Location: East coast
- Contact:
- Cat Man
- Major
- Posts: 420
- Joined: Thu Jul 20, 2006 9:55 pm
- Location: Green Bay WI
Winch Data Plate
Snow man, Those plates look great. I need a winch data plate for mine. Are they available?
Post or send a PM.
Thanks
Cat Man
Post or send a PM.
Thanks
Cat Man
40 Years An Engine Guy
30 Years A Caterpillar Guy
Still Learning Every Day
30 Years A Caterpillar Guy
Still Learning Every Day
-
- Captain
- Posts: 210
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Switzerland
Snowman, where did you buy these bed plates and how much did they cost?
1942 GMC CCKW 353 cargo closed cab with steel bed
1943 Dodge WC 63 (6x6)
1944 Jeep Willys
1943 steel Ben Hur trailer
194? 1 ton Buffalo water trailer
194? 1/4 ton Bantam trailer
Link to see my vehicules: http://ledog.forumgmc.com
-
- First Lieutenant
- Posts: 164
- Joined: Thu Jun 08, 2006 1:10 am
- Location: Linden, NC/Ft Bragg
Bed data plate
Do you have the data plates for a late war composate bet 353?
As my bed data plates are missing also, but they did put the screws back after they removed the plates. Which was nice of them.
As my bed data plates are missing also, but they did put the screws back after they removed the plates. Which was nice of them.
ATW,
Doc Britton.
1945 353-B2 W/W with 1943 Trackson Co. M-36 Gun Mount
1944 Ford M-20 Armored Car
1943 Steel body Ben Hur trailer
1944 MB w/GPW engine (project) On hold M-20 restoration has OPERATIONAL PRIORITY
Active Duty Paratrooper 82nd Abn. Div.
2nd BDE. 325 A.I.R.
3rd BCT 2-505 P.I.R
407th BSB Trauma Team SGT/Leader
Combat Medic
Fmr. Combat Engr. 307th Engr. Bn. Abn.
14 years in the 82nd. Americas Guard of Honor
Doc Britton.
1945 353-B2 W/W with 1943 Trackson Co. M-36 Gun Mount
1944 Ford M-20 Armored Car
1943 Steel body Ben Hur trailer
1944 MB w/GPW engine (project) On hold M-20 restoration has OPERATIONAL PRIORITY
Active Duty Paratrooper 82nd Abn. Div.
2nd BDE. 325 A.I.R.
3rd BCT 2-505 P.I.R
407th BSB Trauma Team SGT/Leader
Combat Medic
Fmr. Combat Engr. 307th Engr. Bn. Abn.
14 years in the 82nd. Americas Guard of Honor